欢迎访问www.483.net-新莆京www483net|官网官方网站!

全国咨询热线

0531-83542917

133-3515-9899

资讯中心

联系大家

电话:0531-83542917 61321776

手机:13954160118

传真:0531-83383866 61321776

邮编:250212

地址:山东章丘辛寨经济开发区

您现在的位置:www.483.net > 资讯中心 > 企业资讯

企业资讯

空气喷涂故障产生原因及应对措施

文章发布: 发表时间: 2017-06-23 10:11:20

据专家先容,为了获得润滑、平坦、均匀共同的涂层,喷漆时必定要留意把握准确的操作方法,否则就会呈现毛病。例如,喷枪漏气、喷雾不良、枪身漏料等景象。下面就这些空气喷涂毛病剖析一下。
According to experts, in order to obtain lubrication, flat, uniform and common coating, spray paint must pay attention to grasp the correct method of operation, otherwise it will appear defective. For example, the spray gun, spray gun, air leakage and other bad scene. Here's an analysis of these air spray faults.
空气喷涂毛病发生因素:
Factors affecting air spraying:
1、喷枪漏气。发生漏气的因素是因为滚珠与气孔没有密封或许喷嘴没有扭紧。
1 、 the spray gun leaks. Because of the leakage factors of ball and no seal may not tighten the nozzle hole.
2、喷雾不良。这是最常见的一种毛病,有许多因素都会致使喷雾不良,例如,涂料的黏度过大;储漆罐的涂料用完;压缩空气压力过低;出漆量过大;压缩空气内含有水分等。
2, poor spray. This is a kind of the most common problems, there are many factors that will cause the bad spray paint, for example, the viscosity is too large; run out of storage tank paint coating; compressed air pressure is too low; the paint quantity is too large; the compressed air contains water etc..
3、枪身漏料。针阀后端的填料失效;压紧螺母太松;喷嘴压紧螺母松或许针形阀磨损都会致使枪身漏料。
3, the body material leakage. The back end of the needle valve packing failure; nut loose; nozzle nut loose or a needle valve wear will cause leakage gun.
空气喷涂毛病的解决方法:
Solutions to air spray defects:
a.处理喷枪漏气只需要用砂蜡将滚珠与气孔周围研磨润滑即可。如果是松了,只需要扭紧喷嘴,留意接口处的连接就好。
A. handling spray gun leakage, only sand and wax ball and air around the grinding lubrication. If it is loose, only need to tighten the nozzle, the interface is connected to the good.
b.抵挡喷雾不良,能够恰当参加一些稀释剂;也能够填充涂料;要留意调整并保持压力;压力过大的话要留意减压;放掉压缩空气气包内的积水。
B. is resistant to spray, and can take part in some thinner. It can also fill the paint; pay attention to adjust and keep the pressure; if the pressure is too great, pay attention to the decompression; release the air in the compressed air bag.
c.枪身漏料能够更换填料或是扭紧螺母又或是以砂、蜡研磨直到它紧密。
C. can replace the packing material leakage gun or nut or on the sand, wax polish until it is close.

 

 

了解更多详情,请搜索:烤漆房,喷塑烤房,新莆京www483net www.483.net-新莆京www483net|官网 / 欢迎您的光临!

XML 地图 | Sitemap 地图